Kako iskoristiti stari MaxTV STB

Its very slow..

Currently 1 running tasks (4867 of 9773):
0: dvdauthor-0.7.2+gitAUTOINC+40f578bce8-r1 do_package (pid 1341)

Slowly, but will be ready:

openatv/build-enviroment/builds/openatv/release/spark7162/tmp/sstate-control/manifest-spark7162-enigma2-skindefault-master.populate_sysroot not found
Currently 2 running tasks (9161 of 9773):
0: enigma2-skins-openvix-2.1+gitAUTOINC+150bc8a00f-r2 do_package (pid 16753)
1: openssl-old-0.9.8x-r17.0 do_package (pid 16995)

 Tasks Summary: Attempted 9773 tasks of which 8920 didn't need to be rerun and all succeeded

Ready for openatv 5.1 image.

The e2jffs2.img enough to rename rootfs.img, or even something has to be convert before the usb start command?

Rename, run, but error; kernel panic:

Creating 7 MTD partitions on "stm-nand-flex.0":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000b00000 : "Spark kernel"
0x000000b00000-0x000001200000 : "Reserve0"
0x000001200000-0x000001400000 : "Reserve1"
0x000001400000-0x000018000000 : "Spark Userfs"
mtd: partition "Spark Userfs" extends beyond the end of device "stm-nand-flex.0" -- size truncated to 0x6c00000
0x000018000000-0x000018800000 : "kernel"
mtd: partition "kernel" is out of reach -- disabled
0x000018800000-0x00001ff00000 : "rootfs"
mtd: partition "rootfs" is out of reach -- disabled
stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
boot-ECC 0x00000000->0x00100000
eth0: device MAC address
 No MAC Management Counters available
IP-Config: Gateway not on directly connected network.
inconsistent device description
List of all partitions:
1f00            1024 mtdblock0 (driver?)
1f01           10240 mtdblock1 (driver?)
1f02            7168 mtdblock2 (driver?)
1f03            2048 mtdblock3 (driver?)
1f04          110592 mtdblock4 (driver?)
No filesystem could mount root, tried:  jffs2
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,6)

What can be wrong?

could mount root...

Hi!

Replace bootargs root=/dev/mtdblock6 rootfstype=jffs2 to root=/dev/mtdblock4 rootfstype=jffs2 ? (I try to, not work...)

These modifications exactly how to do it, I'm still a beginner.

The sparkone be a good choice, or any other such amikoalien?

Replace pkt4 uimage, error is the same as 2015 HDMU 3505:

Empty flash at 0x039a76d8 ends at 0x039a77a8.....

 1. Kriva tema

 2. Use google - https://goo.gl/sO69le

Git repository for Albis STB8000.Kernel,u-boot,patch,firmware.

Modificirani firmware za spark7162 od pkteam-a(12.2015) za Albis STB8000.

In folder firmware read update_firmware.

No need update u-boot.bin because is update u-boot can brick STB.

Format usb in fat32 format and copy rootfs.img and uImage on usb and put usb in STB.

If use old u-boot mtdparts is wrong you need change setenv

PDK7105>setenv update_kernel_usb "usb start; fatload usb 0:1 $load_addr uImage; nand erase 0x0 0x800000; nand write.jffs2 $load_addr 0x0 0x300000"

PDK7105>setenv update_rootfs_usb "usb start; fatload usb 0:1 $load_addr rootfs.img; nand erase 0x800000 0x4400000; nand write $load_addr 0x800000 0x4400000"

PDK7105>setenv update_all_usb "run update_kernel_usb; run update_rootfs_usb"

PDK7105>setenv bootargs "console=ttyAS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2 init=/bin/devinit nwhwconf=device:eth0,hwaddr:$ethaddr ip=$ipaddr:$serverip:$gatewayip:$netmask:Enigma2:eth0:off coprocessor_mem=4m@0x40000000,4m@0x40400000 bigphysarea=6144"

PDK7105>setenv bootcmd "nand read $load_addr 0x0 0x300000; bootm $load_addr"

PDK7105>save

PDK7105>run update_all_usb

PDK7105>reset

Don't copy and paste all.

copy

setenv update_kernel_usb "usb start; fatload usb 0:1 $load_addr uImage; nand erase 0x0 0x800000; nand write.jffs2 $load_addr 0x0 0x300000"

paste in STB u-boot

copy

setenv update_rootfs_usb "usb start; fatload usb 0:1 $load_addr rootfs.img; nand erase 0x800000 0x4400000; nand write $load_addr 0x800000 0x4400000"

paste in STB u-boot

.

.

.

save

run update_all_usb

reset

setenv update_kernel_usb "usb start; fatload usb 0:1 $load_addr uImage; nand erase 0x0 0x800000; nand write.jffs2 $load_addr 0x0 0x300000"

setenv update_rootfs_usb "usb start; fatload usb 0:1 $load_addr rootfs.img; nand erase 0x800000 0x4400000; nand write $load_addr 0x800000 0x4400000"

setenv update_all_usb "run update_kernel_usb; run update_rootfs_usb"

setenv bootargs "console=ttyAS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2 init=/bin/devinit nwhwconf=device:eth0,hwaddr:$ethaddr ip=$ipaddr:$serverip:$gatewayip:$netmask:Enigma2:eth0:off coprocessor_mem=4m@0x40000000,4m@0x40400000 bigphysarea=6144"

setenv bootcmd "nand read $load_addr 0x0 0x300000; bootm $load_addr"

save

run update_all_usb

reset

P.S

#################

turulbird contact me direct.

#################

Try load uImage from usb.

PDK7105>usb start

PDK7105>fatload usb 0:1 $load_addr uImage

PDK7105>bootm $load_addr

Please run

PDK7105>print

and send me.

Try format usb and copy uImage again on usb.

Its run!

Send log. Dont send, too big:

___________ ___ _____________
\________ \ | | / _____ ____/
_____) | | |_/ / | | .---. ,--. _ .--..--.
| ___/ | __'. | | / /__\\ `'_\ : [ `.-. .-. |
| | | | \ \ | | | \__., // | |, | | | | | |
|_| |_| |_| |_| '.__.' \'-;__/ [___||__||__]

----------============ Polish Koders Team ============-----------

AT plugin not found
SerienRecorder plugin not found
ER plugin not found
[OpenWebif] no plugins to load
[OpenWebif] started on 80
< 50.968563> [eMainloop::processOneEvent] unhandled POLLERR/HUP/NVAL for fd 34(16)
File "/var/etc/clean", line 1
SyntaxError: Non-ASCII character '\xd1' in file /var/etc/clean on line 1, but no encoding declared; see http://python.org/dev/peps/pep-0263/ for details

On dropbox is ok firmware.

link

I don,t now what are you doing.I flash firmware several time and all time work.

You doing something wrong.Try download from dropbox and format usb and flash again.

Send me lircd.conf for albis remote and i put in lircd.conf for multi remote.

Problem for exit button is in pkt image.

In lircd.conf change KEY_EXIT to KEY_HOME.

Must send all lircd.conf send me to mail.