Kako iskoristiti stari MaxTV STB

Probaj samo tx rx i ground, ako ne bude radilo probaj 3,3 tx rx i ground.

Nikako ne 5v.

Reversed from U-Boot source and STi7105 datasheet:

J1 is front panel header (both display and keys).

U2 and CN2 is a smartcard interface (U2 is connected to PIO0 which is defined as smartcard interface, and most likely it's just a level converter). Comment from source code:* SC0DATAOUT_1 is on 0/0 (bidirectional)
* SC0DATAOUT_1 is on 0/1 (input)
* SC0EXTCLK_1 is on 0/2 (input)
* SC0CLK_1 is on 0/3 (output)
* SC0RESET_1 is on 0/4 (output)
* SC0CMDVCC_1 is on 0/5 (output)
* 5V3V_1 is on 0/6 (output)
* SC0DET_1 is on 0/7 (input)

HEAD2 is JTAG header. http://www.avi-plus.com/categories/repair-tips-forum/repair-tips-forum/st40-stb71xx-jtag-interfacing.html

CN1 is molex power connector for HDD. There are some components missing but it's not hard to get it working.

PCI is Type III Mini PCI connector, probably used for WLAN as there is a WLAN LED defined in U-Boot source. http://pinouts.ru/Slots/mini_pci_pinout.shtml

JUMP1 is one of 4 hardware interrupt lines.

SW2 is HW reset.

Pozz,

jedno malo drugacije pitanje... :)

Korisnik sam OptiTV-a, STB je Albis SG 8000 koji steka u zadnje vrijeme. Imam od T-shrota isto Albis. Postoji mogucnost force-anja t-com albisa da napravi upgrade sw-a na optimu?

Hvala

Thanx, reset optiminog je izgleda pomogao... Ovaj drugi ne povlaci sw od optime. Mozda zbog MAC addr i serial no., nisam lotao uart da mijenjam uboot varijable.

Hi!

PKT Hyperion v4 good.

HDMU not...

Nije probijen jer se nema što probiti u slučaju Albisa. O custom firmwareu diskutiramo već 2-3 stranice i imaš link na Dropbox gdje imaš 3-4 komada za isprobavanje.

O kojem uređaju pričaš?

Tzv. "security torx", T8 s rupom u sredini, imaš ih na eBayu. Alternative čekanju paketa 2-6 tjedana:

1) zarezati šerafe po sredini s pilom za metal da ih možeš otvoriti s ravnim šerafcigerom

2) s nečim jako tvrdim slomiti čepiće u sredini da paše obični T8

3) jako čvrst mali ravni šerafciger zaglaviti unutra kao na slici i otvara se bez većih problema, samo mora biti čvrst.

Možda sam več pitao ali ne sječam se da sam dobio odgovor.
Može li na modificiranom Albisu sc8000 raditi koji wifi stick?

Da ako imaš adekvatan 0,5 mm (ili čak i manji) borer i dosta preciznu stupnu bušilicu ili glodalicu - nije rješenje za svakog.

Hello!

The JTAG yet unfortunately it did not work (resistors, I tried the uctap also do not know the unknown jkeys.def M28W160FS IRD).
I have Ubuntu 4.14 (Zorin Lite) STlinux of 2.4.
stlinux2.4 If you complete the U-boot file , spit out the command line interface allows serial port for Flash?
Stlinux flash can not be somehow load the necessary files?
currently just learning what this STlinux ... 

Thank you!

     http://www.stlinux.com/u-boot/target-install

I'm trying:

(GDB) sh4tp TARGET: pdk7105: ST40, quiet = 1
The target is assumed to be little endian
SHDEBUG [ERROR] :: Unknown name STMC target TARGET
can not connect to the remote target TARGET: pdk7105: ST40, quiet = 1
(gdb)

Target pdk7105 is ok?

Other:

https://github.com/Polo35/STMC2_Emulator

Hi!

FT4232 / 2232, USB JTAG NT there is currently no.

I know I should, but I try to look for different solutions.

UcTap partially worked for some people, or make a wiggler, it would be enough if you just go up the uboot ...

If you spend over stlinux attributed to the uboot file, serial port can not be
load perhaps?
So far not succeeded,  ...I'm trying.

Try dumping the flash first, if you get 2MB file then it's the simplest way of telling that it works. Then upload it and give us the link to confirm.

Postoji otključani bootloader i neki zamjenski softveri, ali ništa konkretnog.

Znači u biti je to za smeće?

Ima nešto! Pokušat ću sutra ... paralelno i serijski karticu.

Otkrio sam novi Pionero V5:

Kraj, IC je otišao ...